EE - Escola de Engenharia
URI permanente desta comunidadehttps://rihomolog.furg.br/handle/1/512
Navegar
16 resultados
Resultados da Pesquisa
- ItemNumerical analysis including pressure drop in oscillating water column device.(2015) Gomes, Mateus das Neves; Santos, Elizaldo Domingues dos; Isoldi, Liércio André; Rocha, Luiz Alberto OliveiraThe wave energy conversion into electricity has been increasingly studied in the last years. There are several proposed converters. Among them, the oscillatingwater column (OWC) device has been widespread evaluated in literature. In this context, the main goal of this work was to perform a comparison between two kinds of physical constraints in the chimney of the OWC device, aiming to represent numerically the pressure drop imposed by the turbine on the air flow inside the OWC. To do so, the conservation equations of mass,momentumand one equation for the transport of volumetric fraction were solved with the finite volume method (FVM). To tackle thewater-air interaction, the multiphase model volume of fluid (VOF)was used. Initially, an asymmetric constraint inserted in chimney duct was reproduced and investigated. Subsequently, a second strategywas proposed,where a symmetric physical constraint with an elliptical shapewas analyzed. Itwas thus possible to establish a strategy to reproduce the pressure drop in OWC devices caused by the presence of the turbine, as well as to generate its characteristic curve.
- Item3D numerical analysis about the shape influence of the hydro-pneumatic chamber in an oscillating water column (owc).(2015) Isoldi, Liércio André; Grimmler, Juliana do Amaral Martins; Letzow, Max; Souza, Jeferson Avila; Gomes, Mateus das Neves; Rocha, Luis Alberto Oliveira; Santos, Elizaldo Domingues dosThe oceans represent one of the major energy natural resources, which potentially can be used to supply the World energy demand. In the last decades some devices to convert the wave ocean energy into electrical energy have been studied. In this work the operating principle of an Oscillating Water Column (OWC) converter was analyzed with a transient 3D numerical methodology, using the Finite Volume Method (FVM) and the Volume of Fluid (VOF) model. The incident waves on the OWC hydropneumatic chamber cause an oscillation of the water column inside the chamber producing an alternate air flow through the chimney. The air drives a turbine that is coupled to an electric generator. The aim of this work was to investigate the shape influence of the hydro-pneumatic chamber geometry in the air flow. For this, six cases were studied in laboratory scale and the results showed that the variation of the OWC chamber shape can improve 12.4% the amount of mass air flow.
- ItemNumerical analysis of a regular wave over a vertical pile with a square section(2010) Teixeira, Paulo Roberto de Freitas; Gomes, Mateus das Neves; Santos, Elizaldo Domingues dos; Isoldi, Liércio André; Rocha, Luiz Alberto OliveiraThe study of the action of waves on piles is very important for the design of structures in coastal and oceanic areas. Currently, there is strong interest in analyzing the action of waves on piles with non-circular sections, such as rectangular or square ones. According to Vengatesan et al. (2000), the main reason for this interest is the low cost of the connections of the members in the structures with these sections. The objective of this paper is to analyze the action of a regular wave on a vertical pile with a square section employing two differents numerical methodologies for prediction of the wave fluid dynamic. To achieve this goal were used the FLUINCO and FLUENT® softwares. FLUINCO (Teixeira, 2001) employs a partitioned two-step semi-implicit Taylor-Galerkin method in the Navier-Stokes equations. The free surface is governed by its kinematic boundary condition and an arbitrary Lagrangian-Eulerian (ALE) formulation is used to enable movements of the free surface. The FLUENT® code (2006), version 6.3.26, implements a finite volume technique to solve the equation of continuity and the Navier-Stokes equations. The free surface is described by using the VOF method (Volume Of Fluid). The wave period of the studied problem is 4s and its height is 0.05 m. The pile is seated on the bottom and located in the center of a channel. The dimensions of the pile section are 1m × 1m and the channel is 30m long, 10m wide and 1m deep. This paper shows the results obtained by the models in terms of the velocity vectors, the deformation of the free surface and the drag force caused by the wave on the pile. The total horizontal force acting on the pile was analytically calculated using the Morison equation. It was observed very similar results to the numerical ones.
- ItemTwo-dimensional geometric optimization of an oscillating water column converter of real scale(2013) Gomes, Mateus das Neves; Santos, Elizaldo Domingues dos; Isoldi, Liércio André; Rocha, Luiz Alberto de OliveiraThe present paper presents a two-dimensional numerical study about the geometric optimization of an ocean Wave Energy Converter (WEC) into electrical energy. The operational principle is based on the Oscillating Water Column (OWC). The main goal is to seek for the optimal geometry which maximizes the absorbed power take off (PTO) when it is subjected to a defined wave climate. To do so, Constructal Design is employed varying the degree of freedom (DOF) H1/L (ratio between the height and length of OWC chamber) and H3 (lip submergence), while the other DOF H2/l (ratio between height and length of chimney) is kept fixed. Moreover, the chamber and total areas of OWC device are also kept fixed, being the problem constraints. In this study was adopted a regular wave with real scale dimensions. For the numerical solution it is used the Computational Fluid Dynamic (CFD) commercial code FLUENT®, based on the Finite Volume Method (FVM). The multiphasic Volume of Fluid (VOF) model is applied to tackle with the water-air interaction. The computational domain is represented by an OWC device coupled with the wave tank. The results led to a theoretical recommendation about the chamber geometry which maximizes the device performance, indicating that the higher efficiency (around 40 %) is obtained when H1/L = 0.13 and H3 = 9.50 m. On the other hand, the chamber geometry that generate the lower efficiency (around 4.4 %) is formed by H1/L = 0.03 and H3 = 9.00 m. One can note that the optimal shape is approximately 10 times more efficient than the worst geometry, showing the applicability and relevance of the Constructal Design method in the design of OWC-WEC.
- ItemComputational modeling of the air-flow in an oscillating water column system(2009) Gomes, Mateus das Neves; Olinto, Cláudio Rodrigues; Isoldi, Liércio André; Souza, Jeferson Avila; Rocha, Luiz Alberto de OliveiraSeveral alternatives for electric power production have been studied in the last decades. Because of the huge energetic resources stored in the oceans in the form of wave - about 2TW - value that is compared to the annual rate of electric power used in the earth, the conversion of the wave’s energy of the oceans in electric power comes up important as one of these alternatives. One of the ways to make that conversion is through the oscillating water column (OWC) system: the wave enters into the hydro-pneumatic chamber (resembling a cave with entry below the waterline) and the up-and-down movement of water column inside the chamber makes air flow to and from the atmosphere, driving an air turbine. The turbine is symmetric and is driven indifferently in which direction the air flows. This paper presents the computational modeling of the air flow in a oscillating water column chamber using two different methodologies: in one of them it is considered just the chamber, varying the velocity in its entrance according to the wave’s equation, considering just the air, and a new one considering the chamber put into a wave’s tank, so it takes in account the complete interaction between water and air into the chamber. In this method, to consider the water and air it is used the multiphase model volume of fluid (VOF). It was simulated the same geometric compound of an oscillating water column system with a vertically placed tower, in order to compare these two different numerical models. It is noted that the dimensions of the tested chamber are in laboratory scale and the proposed model was used to simulate a 2D case. It was used GAMBIT® software for geometry creation and mesh generation, while FLUENT® package was employed for solving the conservation equations and analysis of the results.
- ItemAnálise de malhas para geração numérica de ondas em tanques(2012) Gomes, Mateus das Neves; Isoldi, Liércio André; Santos, Elizaldo Domingues dos; Rocha, Luiz Alberto OliveiraEste trabalho apresenta uma metodologia para a geração numérica de ondas em tanques e também um estudo de malhas a serem utilizadas em simulações numéricas da propagação de ondas regulares bidimensionais em tanques. São testados dois tipos de geração e refinamento de malhas. Assim busca-se encontrar uma malha independente que forneça resultados com acurácia e com menor esforço computacional. Foram realizadas simulações numéricas da geração de ondas através do pacote FLUENT® , que é baseado no Método de Volumes Finitos (MVF). Foi empregado o modelo multifásico Volume of Fluid (VOF) para reproduzir a propagação da onda no tanque. Esses resultados poderão ser utilizados em trabalhos futuros, principalmente no estudo numérico de dispositivos para conversão de energia das ondas do mar em energia elétrica, como por exemplo, os dispositivos de coluna de água oscilante (OWC) e de galgamento.
- ItemComputational modeling of a regular wave tank(2009) Gomes, Mateus das Neves; Olinto, Cláudio Rodrigues; Rocha, Luiz Alberto Oliveira; Souza, Jeferson Avila; Isoldi, Liércio AndréThis paper presents two different numerical methodologies to generate regular gravity waves in a wave tank. We performed numerical simulations of wave generation through the FLUENT® package, using the Volume of Fluid (VOF) multiphase model to reproduce the wave propagation in the tank. Thus it was possible to analyze two methods for generating regular waves that could be used in future work, especially in the study of devices of energy conversion from ocean waves into electrical energy.
- ItemNumerical analysis of an oscillating water column converter considering a physical constraint in the chimney outlet(2014) Gomes, Mateus das Neves; Seibt, Flávio Medeiros; Rocha, Luiz Alberto Oliveira; Santos, Elizaldo Domingues dos; Isoldi, Liércio AndréThis work presents a 2D numerical study of an Oscillating Water Column (OWC) converter considering physical constraints in its outlet chimney to represent the turbine pressure drop. Two strategies were adopted. The first considers different dimensions for a physical constraint similar to an orifice plate, being the analysis performed in a laboratory scale. After that, other physical restriction with geometry similar to a rotor turbine was investigated in a real scale by means a dimensional variation. The numerical results indicate the importance of consider the pressure drop caused by turbine in the analysis of the OWC behavior.
- ItemComputational modeling applied to the study of wave energy converters (WEC)(2014) Seibt, Flávio Medeiros; Letzow, Max; Gomes, Mateus das Neves; Souza, Jeferson Avila; Rocha, Luiz Alberto Oliveira; Santos, Elizaldo Domingues dos; Isoldi, Liércio AndréThe employment of numerical methods to solve engineering problems is a reality, as well as, the worldwide concern about the need of renewable and alternative energy sources. Thus, this work presents a computational model capable of simulating the operating principle of some Wave Energy Converters (WEC). To do so, the device is coupled in a wave tank, where the sea waves are reproduced. The Finite Volume Method (FVM) and the Volume of Fluid (VOF) model are adopted. The results showed that the converter's operating principle can be numerically reproduced, demonstrating the potential of computational modeling to study this subject.
- ItemTwo-dimensional geometric optimization of an oscillating water column converter in laboratory scale(2012) Gomes, Mateus das Neves; Nascimento, Cristina Dias do; Bonafini, Beatriz Leandro; Santos, Elizaldo Domingues dos; Isoldi, Liércio André; Rocha, Luiz Alberto OliveiraThe present paper presents a two-dimensional numerical study about the geometric optimization of an ocean Wave Energy Converter (WEC) into electrical energy that has as operational principal the Oscillating Water Column (OWC). To do so, the Constructal Design fundamentals were employed to vary the degree of freedom H1/L (ratio between height and length of the OWC chamber), while the other degree of freedom H2/l (ration between height and length of chimney) was kept constant. The OWC chamber area (φ1) and the total OWC area (φ2) are also kept fixed, being the problem constraints. In this study was adopted a regular wave with laboratory scale dimensions. The main goal was to optimize the device’s geometry aiming to maximize the absorbed power when it is subjected to a defined wave climate. For the numerical solution it was used the Computational Fluid Dynamic (CFD) commercial code FLUENT®, which is based on the Finite Volume Method (FVM). The multiphasic Volume of Fluid (VOF) model was applied to treat the water-air interaction. The computational domain was represented by an OWC device coupled into a wave tank. Thereby, it was possible to analyze the WEC subjected to regular wave incidence. An optimal geometry was obtained for (H1/L)o=0.84, being this one approximately ten times more efficient then the worst case (H1/L = 0.14), showing the applicability of Constructal Design in this kind of engineering problem.