EE - Escola de Engenharia
URI permanente desta comunidadehttps://rihomolog.furg.br/handle/1/512
Navegar
10 resultados
Resultados da Pesquisa
- Item3D numerical analysis about the shape influence of the hydro-pneumatic chamber in an oscillating water column (owc).(2015) Isoldi, Liércio André; Grimmler, Juliana do Amaral Martins; Letzow, Max; Souza, Jeferson Avila; Gomes, Mateus das Neves; Rocha, Luis Alberto Oliveira; Santos, Elizaldo Domingues dosThe oceans represent one of the major energy natural resources, which potentially can be used to supply the World energy demand. In the last decades some devices to convert the wave ocean energy into electrical energy have been studied. In this work the operating principle of an Oscillating Water Column (OWC) converter was analyzed with a transient 3D numerical methodology, using the Finite Volume Method (FVM) and the Volume of Fluid (VOF) model. The incident waves on the OWC hydropneumatic chamber cause an oscillation of the water column inside the chamber producing an alternate air flow through the chimney. The air drives a turbine that is coupled to an electric generator. The aim of this work was to investigate the shape influence of the hydro-pneumatic chamber geometry in the air flow. For this, six cases were studied in laboratory scale and the results showed that the variation of the OWC chamber shape can improve 12.4% the amount of mass air flow.
- ItemTwo-dimensional geometric optimization of an oscillating water column converter of real scale(2013) Gomes, Mateus das Neves; Santos, Elizaldo Domingues dos; Isoldi, Liércio André; Rocha, Luiz Alberto de OliveiraThe present paper presents a two-dimensional numerical study about the geometric optimization of an ocean Wave Energy Converter (WEC) into electrical energy. The operational principle is based on the Oscillating Water Column (OWC). The main goal is to seek for the optimal geometry which maximizes the absorbed power take off (PTO) when it is subjected to a defined wave climate. To do so, Constructal Design is employed varying the degree of freedom (DOF) H1/L (ratio between the height and length of OWC chamber) and H3 (lip submergence), while the other DOF H2/l (ratio between height and length of chimney) is kept fixed. Moreover, the chamber and total areas of OWC device are also kept fixed, being the problem constraints. In this study was adopted a regular wave with real scale dimensions. For the numerical solution it is used the Computational Fluid Dynamic (CFD) commercial code FLUENT®, based on the Finite Volume Method (FVM). The multiphasic Volume of Fluid (VOF) model is applied to tackle with the water-air interaction. The computational domain is represented by an OWC device coupled with the wave tank. The results led to a theoretical recommendation about the chamber geometry which maximizes the device performance, indicating that the higher efficiency (around 40 %) is obtained when H1/L = 0.13 and H3 = 9.50 m. On the other hand, the chamber geometry that generate the lower efficiency (around 4.4 %) is formed by H1/L = 0.03 and H3 = 9.00 m. One can note that the optimal shape is approximately 10 times more efficient than the worst geometry, showing the applicability and relevance of the Constructal Design method in the design of OWC-WEC.
- ItemComputational modeling of the air-flow in an oscillating water column system(2009) Gomes, Mateus das Neves; Olinto, Cláudio Rodrigues; Isoldi, Liércio André; Souza, Jeferson Avila; Rocha, Luiz Alberto de OliveiraSeveral alternatives for electric power production have been studied in the last decades. Because of the huge energetic resources stored in the oceans in the form of wave - about 2TW - value that is compared to the annual rate of electric power used in the earth, the conversion of the wave’s energy of the oceans in electric power comes up important as one of these alternatives. One of the ways to make that conversion is through the oscillating water column (OWC) system: the wave enters into the hydro-pneumatic chamber (resembling a cave with entry below the waterline) and the up-and-down movement of water column inside the chamber makes air flow to and from the atmosphere, driving an air turbine. The turbine is symmetric and is driven indifferently in which direction the air flows. This paper presents the computational modeling of the air flow in a oscillating water column chamber using two different methodologies: in one of them it is considered just the chamber, varying the velocity in its entrance according to the wave’s equation, considering just the air, and a new one considering the chamber put into a wave’s tank, so it takes in account the complete interaction between water and air into the chamber. In this method, to consider the water and air it is used the multiphase model volume of fluid (VOF). It was simulated the same geometric compound of an oscillating water column system with a vertically placed tower, in order to compare these two different numerical models. It is noted that the dimensions of the tested chamber are in laboratory scale and the proposed model was used to simulate a 2D case. It was used GAMBIT® software for geometry creation and mesh generation, while FLUENT® package was employed for solving the conservation equations and analysis of the results.
- ItemNumerical analysis of an oscillating water column converter considering a physical constraint in the chimney outlet(2014) Gomes, Mateus das Neves; Seibt, Flávio Medeiros; Rocha, Luiz Alberto Oliveira; Santos, Elizaldo Domingues dos; Isoldi, Liércio AndréThis work presents a 2D numerical study of an Oscillating Water Column (OWC) converter considering physical constraints in its outlet chimney to represent the turbine pressure drop. Two strategies were adopted. The first considers different dimensions for a physical constraint similar to an orifice plate, being the analysis performed in a laboratory scale. After that, other physical restriction with geometry similar to a rotor turbine was investigated in a real scale by means a dimensional variation. The numerical results indicate the importance of consider the pressure drop caused by turbine in the analysis of the OWC behavior.
- ItemTwo-dimensional geometric optimization of an oscillating water column converter in laboratory scale(2012) Gomes, Mateus das Neves; Nascimento, Cristina Dias do; Bonafini, Beatriz Leandro; Santos, Elizaldo Domingues dos; Isoldi, Liércio André; Rocha, Luiz Alberto OliveiraThe present paper presents a two-dimensional numerical study about the geometric optimization of an ocean Wave Energy Converter (WEC) into electrical energy that has as operational principal the Oscillating Water Column (OWC). To do so, the Constructal Design fundamentals were employed to vary the degree of freedom H1/L (ratio between height and length of the OWC chamber), while the other degree of freedom H2/l (ration between height and length of chimney) was kept constant. The OWC chamber area (φ1) and the total OWC area (φ2) are also kept fixed, being the problem constraints. In this study was adopted a regular wave with laboratory scale dimensions. The main goal was to optimize the device’s geometry aiming to maximize the absorbed power when it is subjected to a defined wave climate. For the numerical solution it was used the Computational Fluid Dynamic (CFD) commercial code FLUENT®, which is based on the Finite Volume Method (FVM). The multiphasic Volume of Fluid (VOF) model was applied to treat the water-air interaction. The computational domain was represented by an OWC device coupled into a wave tank. Thereby, it was possible to analyze the WEC subjected to regular wave incidence. An optimal geometry was obtained for (H1/L)o=0.84, being this one approximately ten times more efficient then the worst case (H1/L = 0.14), showing the applicability of Constructal Design in this kind of engineering problem.
- ItemModelagem computacional de um dispositivo do tipo coluna de água oscilante para a costa de Rio Grande(2009) Gomes, Mateus das Neves; Isoldi, Liércio André; Olinto, Cláudio Rodrigues; Rocha, Luiz Alberto Oliveira; Santos, Elizaldo Domingues dos; Souza, Jeferson AvilaEste trabalho apresenta a modelagem computacional de um conversor de energia das ondas do mar em energia elétrica do tipo Coluna de Água Oscilante (CAO) submetido ao clima de ondas da costa da cidade de Rio Grande. A simulação numérica foi realizada utilizando-se o pacote FLUENT® e empregando-se o modelo multifásico Volume of Fluid (VOF) na geração da onda e na interação da mesma com o conversor. O domínio computacional foi representado por um tanque de ondas acoplado ao dispositivo CAO, possibilitando analisar o seu comportamento quando sujeito a incidência de ondas regulares com características semelhantes ao clima de ondas na costa de Rio Grande. Os resultados obtidos demonstram a potencialidade da região em gerar energia elétrica a partir da energia das ondas do mar, através do conversor tipo CAO.
- ItemEnergia das ondas do mar: modelagem computacional de um dispositivo de galgamento(2009) Iahnke, Silvana Letícia Pires; Gomes, Mateus das Neves; Isoldi, Liércio André; Rocha, Luiz Alberto OliveiraEste trabalho apresenta um breve estudo sobre energia das ondas do mar bem como a modelagem computacional de um dispositivo do tipo galgamento. A simulação foi realizada através do software de Dinâmica dos Fluidos Computacional FLUENT®, tendo sido empregado o modelo multifásico Volume of Fluid (VOF), para representar adequadamente a interação entre água e ar. Os resultados obtidos foram satisfatórios, sendo, na geração da onda, a diferença máxima entre os resultados numéricos e a solução analítica, em torno de 4.6%. Foi observado também, que o conhecimento da altura da onda, aliado ao projeto adequado da rampa, são fatores que determinam a ocorrência do galgamento.
- ItemModelagem computacional de um dispositivo do tipo coluna de água oscilante para a costa de Rio Grande(2009) Gomes, Mateus das Neves; Isoldi, Liércio André; Olinto, Cláudio Rodrigues; Rocha, Luiz Alberto Oliveira; Santos, Elizaldo Domingues dos; Souza, Jeferson AvilaEste trabalho apresenta a modelagem computacional de um conversor de energia das ondas do mar em energia elétrica do tipo Coluna de Água Oscilante (CAO) submetido ao clima de ondas da costa da cidade de Rio Grande. A simulação numérica foi realizada utilizando-se o pacote FLUENT® e empregando-se o modelo multifásico Volume of Fluid (VOF) na geração da onda e na interação da mesma com o conversor. O domínio computacional foi representado por um tanque de ondas acoplado ao dispositivo CAO, possibilitando analisar o seu comportamento quando sujeito a incidência de ondas regulares com características semelhantes ao clima de ondas na costa de Rio Grande. Os resultados obtidos demonstram a potencialidade da região em gerar energia elétrica a partir da energia das ondas do mar, através do conversor tipo CAO.
- ItemComputational modeling of an oscillating water column device for the Rio Grande coast(2009) Gomes, Mateus das Neves; Isoldi, Liércio André; Olinto, Cláudio Rodrigues; Rocha, Luiz Alberto Oliveira; Souza, Jeferson AvilaThis work presents the computational modeling of a converter of wave energy in electrical energy. The converter is Oscillating Water Column (OWC) type, submitted to the wave climate of Rio Grande city. The numerical simulation was performed using FLUE)T® package and employing the multiphase Volume of Fluid (VOF) model in the wave generation and in the interaction between the wave and the converter device. The computational domain was represented by a wave tank coupled with the OWC device. This domain allows the behavior analysis to be performed when the device is subjected to the incidence of regular waves. The waves were molded to represent the characteristics of the Rio Grande coastclimate. Results demonstrate that the OWC converter can be successfully used to convert the Rio Grande's coast wave energy in useful electrical energy.
- ItemEnergy from the sea: computational modeling of an overtopping device(2009) Iahnke, Silvana Letícia Pires; Gomes, Mateus das Neves; Isoldi, Liércio André; Rocha, Luiz Alberto OliveiraThis work presents a brief study about the wave energy as well as a computational modeling of an overtopping device. The numerical simulation was performed with the FLUE T® Computational Fluid Dynamic software code, employing the multiphase Volume of Fluid (VOF) model. The obtained results showed a satisfactory agreement between the numerical and analytical solutions, being the maximum difference calculated for the wave generation of approximated 4.6%. It was also observed that the knowledge of the wave height and an adequate ramp design are factors that determine the overtopping occurrence.