EE - Escola de Engenharia
URI permanente desta comunidadehttps://rihomolog.furg.br/handle/1/512
Navegar
20 resultados
Resultados da Pesquisa
- ItemNumerical simulation of FCC risers(2003) Souza, Jeferson Avila; Vargas, Jose Viriato Coelho; Meien, Oscar Felippe von; Martignoni, Waldir PedroThe catalytic cracking of hydrocarbons in a FCC riser is a very complex physical and chemical phenomenon, which combines a three-dimensional, three-phase fluid flow with a heterogeneous catalytic cracking kinetics. Several researchers have carried out the modeling of the problem in different ways. Depending on the main objective of the modeling it is possible to find in the literature very simple models while in other cases, when more accurate results are necessary, each equipment is normally treated separately and a set of differential and algebraic equations is written for the problem. The riser reactor is probably the most important equipment in a FCC plant. All cracking reactions and fuel formation occur during the short time (about 4-5s) that the gas oil stays in contact with the catalyst inside the riser. This work presents a simplified model to predict the, temperature and concentrations in a FCC riser reactor. A bi-dimensional fluid flow field combined with a 6 lumps kinetic model and two energy equations (catalyst and gas oil) are used to simulate the gas oil cracking process. Based on the velocity, temperature and concentration fields, it is intended, on a next step, to use the second law of thermodynamic to perform a thermodynamic optimization of the system.
- ItemA two-phase one-dimensional model for simulation of FCC risers(2006) Brum, Ary Saad; Souza, Jeferson Avila; Vargas, Jose Viriato CoelhoThe FCC (Fluidized Catalytic Cracking) is one of the most important processes in a petroleum refinery plant. The numerical modeling of this process has been performed by several authors who have proposed different mathematical models and reported them in the literature. With the constant increase of computational capabilities, such models have become even more complex and with wider application. The different models address both fluid flow and cracking kinetic, varying from simple one phase and one-dimensional models to three-dimensional and three-phase models. Therefore, there is no common ground regarding the most adequate formulation, and advantages and drawbacks may be identified in each available model. In the present work, a relatively complex model reported in the literature is reproduced. Even though it is a one dimensional model, it includes many physical phenomena, like the dependence of the fluid properties on temperature and the transport equations formulation for both phases (gas and particulate). In a following stage, some simplifications in the mathematical formulation are included to the model and the results obtained with both formulations (with and without simplifications) are compared. The main goal of the present work is to establish a relationship between each included physical phenomenon and its real influence on the capability of the model to predict the products formation inside the riser reactor.
- ItemNumerical simulation of the resin transport through fiber reinforcement medium(SOUZA, Jeferson Avila; ROCHA, Luiz Alberto Oliveira; AMICO, Sandro Campos. Numerical simulation of the resin transport through fiber reinforcement medium. In: INTERNATIONAL CONGRESS OF MECHANICAL ENGINEERING – COBEM, 19., 2007, Brasília. Anais... Brasília: [s.n.], 2007. Disponível em: . Acesso em: 25 jul. 2015., 2007) Souza, Jeferson Avila; Rocha, Luiz Alberto Oliveira; Amico, Sandro CamposThis paper describes the numerical simulation of the RTM (Resin Transfer Molding) process applied to the modeling of the resin transport through a fibrous reinforcement. The molding volume which is to be impregnated with the resin is considered as a porous medium and the Darcy equation is used to determine the resin transport velocity through the mold. A control volume finite element method is used for the determination of the pressure gradients inside the mold and the resin flow front advance is obtained using a FAN technique. The finite volume method was built to be used with a bi-dimensional unstructured grid, hence allowing the discretization of complex geometries. In the simulation presented here, resin physical properties, like viscosity and density, and the permeability of the media were kept constants.
- ItemModeling and simulation of industrial FCC risers(2007) Souza, Jeferson Avila; Vargas, Jose Viriato Coelho; Meien, Oscar Felippe von; Martignoni, Waldir PedroRisers are considered vital parts in Fluidized Catalytic Cracking (FCC) conversion units. It is inside the riser reactor that the heavy hydrocarbon molecules are cracked into lighter petroleum fractions such as liquified Petroleum gas (LPG) and gasoline. The FCC process is considered a key process in the world petroleum industry, since it is the main responsible for the porfitable conversion of heavy gasoil into commercial valuable products. This work presents a simplified transient model to predict the response of a FCC riser reactor, i. e., the fluid flow, temperature and concentrations of the mixture components throughout the riser and at the exit. A bi-dimensional fluid flow field combined with a 6 lumps kinetic model and two energy equations are used to model the gasoil mixture flow and cracking process inside the riser reactor. The numerical results are in good agreement with expetimental data, as a result, the model can be utilized for design, and optimization of FCC units. The simulation herein presented shows the applicability of the proposed method for the numerical simulation and control of industrial riser's units.
- ItemComputational modeling of the resin transfer molding process(2009) Oliveira, Cristiano Peres; Souza, Jeferson Avila; Isoldi, Liércio André; Rocha, Luiz Alberto de Oliveira; Amico, Sandro CamposThe Resin Transfer Molding, or RTM, process has recently become one of the most important processes of fiber reinforced composites manufacturing. The process consists essentially of three stages: “an arrangement of fiber mats in a mold cavity, a mold filling by a polymeric resin and a curing phase”. Most of the difficulties of incorporating RTM occur during the filling stage. To create an acceptable composite part the preform must be completely impregnated with resin. The conditions which most strongly influence the flow are mold geometry, resin rheology, preform permeability, and location of the injection ports and vents. There are different types of RTM process, e.g. RTM Light or VARTM, employed in accordance with the final desired characteristics and properties of composite components. Besides, RTM may also be carried out using multilayers, with distinct characteristics. The numerical simulation of the mold filling stage becomes an important tool which helps the mold designer to understand the process parameters. Considering the fibrous preform as a porous media, the phenomenon can be modeled by Darcy’s law to describe resin flow. This study used two commercial softwares, FLUENT® and PAM-RTM®. FLUENT® is a general Computational Fluid Dynamics (CFD) code, based on Finite Volume Method (FVM). It applies the Volume of Fluid (VOF) method to solve the filling problem because it does not have a specific RTM module. PAM-RTM® is a specific package for RTM problems, based on the Finite Element Method (FEM). These tools were applied to simulate numerically several RTM examples of the resin flow into the mold and the results for both softwares were compared with previous works.
- ItemComputational modeling of the air-flow in an oscillating water column system(2009) Gomes, Mateus das Neves; Olinto, Cláudio Rodrigues; Isoldi, Liércio André; Souza, Jeferson Avila; Rocha, Luiz Alberto de OliveiraSeveral alternatives for electric power production have been studied in the last decades. Because of the huge energetic resources stored in the oceans in the form of wave - about 2TW - value that is compared to the annual rate of electric power used in the earth, the conversion of the wave’s energy of the oceans in electric power comes up important as one of these alternatives. One of the ways to make that conversion is through the oscillating water column (OWC) system: the wave enters into the hydro-pneumatic chamber (resembling a cave with entry below the waterline) and the up-and-down movement of water column inside the chamber makes air flow to and from the atmosphere, driving an air turbine. The turbine is symmetric and is driven indifferently in which direction the air flows. This paper presents the computational modeling of the air flow in a oscillating water column chamber using two different methodologies: in one of them it is considered just the chamber, varying the velocity in its entrance according to the wave’s equation, considering just the air, and a new one considering the chamber put into a wave’s tank, so it takes in account the complete interaction between water and air into the chamber. In this method, to consider the water and air it is used the multiphase model volume of fluid (VOF). It was simulated the same geometric compound of an oscillating water column system with a vertically placed tower, in order to compare these two different numerical models. It is noted that the dimensions of the tested chamber are in laboratory scale and the proposed model was used to simulate a 2D case. It was used GAMBIT® software for geometry creation and mesh generation, while FLUENT® package was employed for solving the conservation equations and analysis of the results.
- ItemComputational modeling of a regular wave tank(2009) Gomes, Mateus das Neves; Olinto, Cláudio Rodrigues; Rocha, Luiz Alberto Oliveira; Souza, Jeferson Avila; Isoldi, Liércio AndréThis paper presents two different numerical methodologies to generate regular gravity waves in a wave tank. We performed numerical simulations of wave generation through the FLUENT® package, using the Volume of Fluid (VOF) multiphase model to reproduce the wave propagation in the tank. Thus it was possible to analyze two methods for generating regular waves that could be used in future work, especially in the study of devices of energy conversion from ocean waves into electrical energy.
- ItemThermal Model for Electromagnetic Launchers(2008) Zhao, Hairong; Souza, Jeferson Avila; Ordonez, Juan CarlosThis paper presents a 3D model for the determination of the temperature field in an electromagnetic launcher. The large amounts of energy that are dissipated into the structure of an electromagnetic launcher during short periods of time lead to a complicated thermal management situation. Effective thermal management strategies are necessary in order to maintain temperatures under acceptable limits. This paper constitutes an attempt to determine the temperature response of the launcher. A complete three-dimensional model has been developed. It combines rigid body movement, electromagnetic effects and heat diffusion together. The launcher consists of two parallel rectangular rails and an armature moving between them. Preliminary results show the current distribution on the rail cross-section, the localized resistive heating, and the rail transient temperature response. The simulation results are compared to prior work presented for a 2D geometry by Powell and Zielinski (2008).
- ItemModelagem computacional de um dispositivo do tipo coluna de água oscilante para a costa de Rio Grande(2009) Gomes, Mateus das Neves; Isoldi, Liércio André; Olinto, Cláudio Rodrigues; Rocha, Luiz Alberto Oliveira; Santos, Elizaldo Domingues dos; Souza, Jeferson AvilaEste trabalho apresenta a modelagem computacional de um conversor de energia das ondas do mar em energia elétrica do tipo Coluna de Água Oscilante (CAO) submetido ao clima de ondas da costa da cidade de Rio Grande. A simulação numérica foi realizada utilizando-se o pacote FLUENT® e empregando-se o modelo multifásico Volume of Fluid (VOF) na geração da onda e na interação da mesma com o conversor. O domínio computacional foi representado por um tanque de ondas acoplado ao dispositivo CAO, possibilitando analisar o seu comportamento quando sujeito a incidência de ondas regulares com características semelhantes ao clima de ondas na costa de Rio Grande. Os resultados obtidos demonstram a potencialidade da região em gerar energia elétrica a partir da energia das ondas do mar, através do conversor tipo CAO.
- ItemModelagem computacional de um dispositivo do tipo coluna de água oscilante para a costa de Rio Grande(2009) Gomes, Mateus das Neves; Isoldi, Liércio André; Olinto, Cláudio Rodrigues; Rocha, Luiz Alberto Oliveira; Santos, Elizaldo Domingues dos; Souza, Jeferson AvilaEste trabalho apresenta a modelagem computacional de um conversor de energia das ondas do mar em energia elétrica do tipo Coluna de Água Oscilante (CAO) submetido ao clima de ondas da costa da cidade de Rio Grande. A simulação numérica foi realizada utilizando-se o pacote FLUENT® e empregando-se o modelo multifásico Volume of Fluid (VOF) na geração da onda e na interação da mesma com o conversor. O domínio computacional foi representado por um tanque de ondas acoplado ao dispositivo CAO, possibilitando analisar o seu comportamento quando sujeito a incidência de ondas regulares com características semelhantes ao clima de ondas na costa de Rio Grande. Os resultados obtidos demonstram a potencialidade da região em gerar energia elétrica a partir da energia das ondas do mar, através do conversor tipo CAO.